Doppler angle
Definition
Doppler angle is the angle between the ultrasound beam and the direction of blood flow, and it should be kept at 60 degrees or less, and consistent between measurements, for an accurate velocity estimate. Because the Doppler equation includes the cosine of this angle, error increases sharply beyond 60 degrees, so small inconsistencies in angle correction produce large velocity errors; at 90 degrees, cosine equals zero and no shift is measured regardless of true flow. Tortuous vessels can make holding 60 degrees difficult.
How Doppler angle Is Tested on the Registry Exam
SPI and vascular questions test that error rises sharply above a 60 degree Doppler angle, and that a 90 degree angle produces zero measurable shift.
ARDMS SPI Exam Overview (2026)
Doppler angle is part of the core curriculum for the Sonography Principles & Instrumentation (Required for RDMS/RDCS/RVT) exam.
- Questions
- 110
- Time Limit
- 2 hours
- Passing Score
- 555 (300-700)
- Test Provider
- Pearson VUE
Official SPI Content Domains
Video Lessons Covering Doppler angle
Review these related video lessons from Prepry's registry review courses.
Textbook & Clinical References
- Edelman, S. K. (2012). Understanding Ultrasound Physics. ESP Ultrasound.
Related Doppler and Hemodynamics Terms
View all 14 terms →Nyquist limit
The Nyquist limit is the highest Doppler shift frequency that pulsed wave or color Doppler can sample and display correctly, equal to half the pulse repetition frequency. A true shift greater than this limit cannot be sampled often enough to display accurately and will alias. Because PRF is tied to depth, decreasing the depth of the sample volume raises PRF and therefore the Nyquist limit, one way to resolve aliasing at high velocities.
Read definition & exam tips →
Aliasing
Aliasing is a display error in pulsed wave and color Doppler where a true velocity exceeding the Nyquist limit is shown incorrectly, wrapping around to appear as flow in the opposite direction. On a spectral waveform the peaks above the limit appear cut off at the top and wrapped to the bottom; on color Doppler it appears as an abrupt switch from one flow color to its opposite. It can be corrected by raising PRF or lowering the baseline; continuous wave Doppler does not alias.
Read definition & exam tips →
Spectral broadening
Spectral broadening is the filling-in of the normally clear window beneath a spectral Doppler waveform, because a wide range of velocities is present in the sample volume at the same instant. It most often signals turbulent flow, such as at or just past a stenosis, but a sample volume that is too large, a Doppler angle that is too steep, or excessive spectral gain can produce it artificially without any true flow disturbance.
Read definition & exam tips →
Peak systolic velocity
Peak systolic velocity, or PSV, is the highest blood flow velocity recorded during the systolic upstroke of the cardiac cycle on a spectral Doppler waveform. Because velocity must rise as a vessel narrows to keep the same volume of flow moving through a smaller area, PSV is the primary value used to grade arterial stenosis severity, with published thresholds such as greater than 230 cm/s for a 70 percent or greater internal carotid artery stenosis under NASCET criteria.
Read definition & exam tips →
End-diastolic velocity
End-diastolic velocity, or EDV, is the blood flow velocity measured at the end of diastole, just before the next systolic upstroke, on a spectral Doppler waveform. It reflects how much forward flow continues through a vessel during the resting phase of the cardiac cycle, which depends on downstream vascular resistance, and it rises alongside peak systolic velocity as an arterial stenosis worsens toward a pre-occlusive lesion. EDV is combined with PSV to calculate the resistive index.
Read definition & exam tips →
Resistive index
Resistive index, or RI, is a Doppler measurement of downstream resistance to flow, calculated as peak systolic velocity minus end-diastolic velocity, divided by peak systolic velocity. A higher RI reflects greater downstream resistance with little or no diastolic flow, while a lower RI reflects a low-resistance bed with substantial forward flow through diastole. The normal renal artery RI is roughly 0.47 to 0.70, and a renal transplant RI above about 0.8 raises concern for transplant dysfunction.
Read definition & exam tips →